How to Fix Power Button iPod Nano 6th Generation

A friend of mine had an iPod Nano 6th Gen that wouldn’t turn on when you press the power button. I will document what I did to fix it here. This article may also be useful for those looking to dismantle or fix their iPod Nano 6th Gen since most of the steps contained here will allow you to access all components of the device. By performing this fix, there is also the chance that you may damage your iPod, so beware of this before you attempt to DIY. I cannot be responsible if you make a mistake! I have fiddled with very small things and have done things that most kids wouldn’t ever do (and adults think is a useless activity), so I can sometimes invent a creative way to make something work.

Step 00 - iPod

You may be looking at the iPod and wondering how on Earth is it possible to open something with no visible screws? It actually isn’t too difficult when you know how. I’ll try to do a step-by-step article 🙂 Please note that fixing the power button will either require you to make a very small “button” to glue onto a small component, or you will need to buy replacement iPod parts.

1.) You will need tools. Preferably you would buy some plastic opening tools from eBay since they are less likely to damage the device. You will also need a small Phillips head screwdriver, usually found in a $2 jeweler’s screwdriver set. A pair of tweezers is good for placing tiny components. A heat source is needed; you can use a hair-dryer, heat gun or just a standard fan-heater. For this fix, I also used “Super-Glue” and contact glue (or rubber cement).

2.) Heat up the iPod using the heat source. You should heat it up until it is warm, but not too hot to touch. Do not overheat the device or you may damage the screen or battery. I used a bathroom heater on the highest setting at a distance of about 10cm. Keep the heater nearby in case the iPod cools down so you can re-soften the glue.

IMG_20130129_191526

3.) When the iPod is nice and warm, place it so that the dock connection point faces you. Using the plastic opening tool, gently pry up the right side of the screen. Don’t force it up or you could cause a crack internally which will give you a screen that looks like one of those “Cracked Screen” phone apps. If you look into the gap, you will see the glue stretching. If you can sever this glue using the tool, knife (carefully),  your fingernail or a business card, it will become easier to remove the screen. Once you have freed the top, bottom and right edges of the screen, pull the screen gently towards the right by holding the top and bottom edges. Be careful not to let the screen suddenly detach, as you don’t want to ruin the data cables. Once all edges of the screen are free, turn the screen over like you are reading a book.

IMG_20130129_191810

4.) On the back of the screen is a shiny mirror with which you can glorify yourself. But you’re not interested in that, right? 😉 Now looking at the inside of the iPod you will see 2 screws – one at the right and one at the bottom left. Undo these with the Phillips head screwdriver. You will notice that the screws are very small and would love to get lost on your floor, so a small magnet to hold them will keep them by your side. Remove the metal plate by turning it like the page of a book. Note how it clips into the bottom right and left top of the iPod shell.

IMG_20130129_204205

5.) At this stage you may want to completely detach the screen by prying off the 2 left-most connectors in the bottom right quadrant. I chose to leave the screen attached, although this probably made things a little awkward. Now using the plastic opening tool, gently pry the battery out from the right-middle. The heater will come in useful here, however, beware of excess heat as lithium batteries don’t like summer. Try to slide the tool under the battery to reduce the chance of it bending. Once the battery is loose, turn it over like another page in this mini-electro-book.

Step 06 - Unscrewing Tab

6.) On the top edge of the iPod shell there are some screws hidden under the black rubber gasket. Unscrew the 2 right-most screws and store them on your magnet. Now comes a more difficult step. You will have to carefully loosen the black tape and the ribbon cable from the inside top edge. Loosen it from the rightmost corner to just past the centre screws. You will notice the ribbon cable is bent into an ‘S’ shape and is stored in a little curved indentation.

IMG_20130129_205553

IMG_20130129_210807

7.) Using a small flat head screwdriver, pry out the little metal tab from the middle joint. Once the back edge is clear, gently pull it towards the left and upwards over the ribbon cable. Be very careful not to overstress the ribbon cable as it is very thin. Do not attempt to pull it out too far! You should find that you can now rotate the metal tab anti-clockwise to see the gold button surface mount component. Do not rotate the tab more than 90 degrees or you risk tearing the cable and rendering useless your volume + power controls! It would be a good idea to study where the cable or tab wants to go, and where it resists. Remember how small they are compared to your fingers…

IMG_20130129_213802

8.) Now for the fidgety bit… I made a very small and thin circular disc or “button” from a piece of thin metal. You could also cut a disc out of thin plastic or a thick sheet of paper soaked in superglue and allowed to dry. The plastic in your driver’s licence or ID card is actually too thick! Something half the thickness should do. If you are unsure, use standard A4 paper soaked in superglue. You can always add one more layer if it ends up not being thick enough. The disc should be only around 1.5mm to 2mm in diameter. A square may suffice if you have trouble with the circle. If you can, try to get a thickness around 0.25mm (thanks ‘sean’).

IMG_20130129_214209

9.) Once you have the disc made, apply a tiny amount of glue to the disc. Use the tweezers to hold the disc by an edge. You can use superglue, or the more forgiving alternative, contact glue. Don’t try applying the glue to the iPod button as Murphy’s Law will mean that the glue will go everywhere except onto the button. Now holding the tab on the iPod, place the disc onto the gold button. Most likely the disc will try to stick to the tweezers, so you may have to try a creative way of twisting the tweezers free while still holding the disc down. If the disc isn’t on centre, you can re-adjust it before the glue dries. This is where contact glue is better, since it won’t have set yet. Let the glue dry for a few minutes to ensure the disc won’t move again.

IMG_20130129_223829

10.) You should re-connect the data cable for the screen so you can test whether the button works. Re-install the metal tab by sliding it back into the corner and back over the ribbon cable, being careful not to twist or crush the cable. Insert the screws and tighten them. Try to turn on the iPod. You should be able to see the screen light up from the back side. If the screen turned on while you were tightening the screws (that’s me!), your disc is too thick! There is a remedy for this – remove the rightmost screw permanently, as it allows a bit more movement. If this doesn’t work, unfortunately you will have to try to remove your disc and make a thinner one. This is where contact glue shines again, as it is easier to remove than superglue and won’t rip out the button.

Step 11 - Improvisation

11.) If everything went well, then you can re-set the ribbon cable and the black tape, then re-insert the battery. Then you can re-install the metal plate, making sure it clips in, especially at the bottom right. Press down there carefully with the Phillips head screwdriver if it doesn’t look flat.

If you had to permanently remove the screw near the button (me), you will need to trim the metal plate near the button tab to allow the movement. Use sharp scissors that aren’t loose and wobbly, since the plate is stainless steel.

12.) Now you will need to make a decision about whether you keep the black gasket, or whether you remove it and use contact glue instead. If the gasket is in good condition and isn’t twisted or lumpy, then you can carefully slide the screen and the data cable into the left side of the iPod. Finally, fold down the rest of the screen and press it down at the edges. You should not be able to slide your fingernail under the screen.

If you found the gasket to be in bad condition, you will need to carefully remove it by scraping with your fingernail and/or the flat head screwdriver. Once it is gone, insert the data cable into the iPod’s left side and hold the screen up with your finger and thumb on the top and bottom edges of the screen. Now comes a tricky part – try to apply the contact glue onto the edges on the iPod shell. Don’t apply too much or it will squash out and make a mess inside and out. Slowly lower the screen into position, making sure the little rubber tab on the right hand side slides in. Apply some weights or light clamping for half an hour to make sure the screen sticks well. Don’t pile on the weights or you risk cracking your screen.

IMG_20130130_031247

Complete! Hopefully now you will have a working iPod power button and won’t have to use a computer or charger to turn it on! You can now go and listen to “Future World Music – Dream Chasers” to celebrate your achievement! If you killed your iPod, there is new music you can listen to – I suggest ‘Elysium Dreams’ by Killer Tracks for your blessed iPod. 🙂

I hope you tinkerers found this useful. The power button is something that shouldn’t usually fail, but when it does, it is most likely just because it moved out of alignment. This fix should be relatively easy if you tinker a lot like me 😉 If you have any questions or have found another way to fix your iPod, then please feel free to share!

Later guys,

Rennie ♪

100 responses to “How to Fix Power Button iPod Nano 6th Generation

  1. I think it doesn’t click as much due to the button being almost pressed already, I’m not sure a metal piece would necessarily do better. If it works, don’t undo it as you will probably only make it worse ;p Remember there is more dis-satisfaction when the button doesn’t work at all XD

  2. Thank you so much for the tutorial!
    I was able to fix the power button but it just doesn’t have the satisfying ‘click’ sound. I put a piece of paper (that was covered in crazy glue and dried). Maybe because it is kindof soft that it doesn’t have the click sound? As opposed to putting a small metal piece?

  3. Jessie, Have you made sure the cables were clicked in correctly? Did you ever stress the cables to the screen? It seems like you could possibly have damaged the cable that sends the images/etc to the screen, or maybe you damaged the connector.

  4. welp my screens broken now, the power button still doesn’t work, and the screen just turns white when I plug it into the ipod dock. Music comes on, but I have no control over it…

  5. It is just the metal plate/button click assembly – it should be in the corner past the two screw holes. In step 7 you can see my finger on the tab – it is covering up the two screw holes but you can see roughly how far it is on that tab. Note that yours will be closer to being in between the tab and the iPod button if you aren’t game to stretch it out like I did.

    Also, plenty of people have ruined their iPod trying to perform this fix. That’s why I said I couldn’t be responsible lol but the thing is they were going to get a new one anyhow so may as well try!

    Any chance you can upload a picture? Remember you can try to use where the actual button is on the outside to gauge the distance it might be from the screw holes. Maybe your button is silver but most likey it is just gold and hidden under the shell still ;p

  6. Great instructions but I must be the only idiot not able to fix it. It’s all apart now and I cannot see the ‘gold button’ in step 7 to stick the tab onto. Maybe I’m being too careful and didn’t pull the metal tab out far enough? So discouraged… i loved my ipod – am hating Apple Corp. and built-in obsolescence.

  7. Thank you so much for the tutorial! My ipod is all fixed and working perfectly now, you saved me about $100 🙂

  8. I mean if you replace the battery, it will be soldered to the circuit board and attached by 2 wires. If you cut the wires near the old battery and strip back some of the insulation, you can then insert the new battery and strip some insulation off the new battery’s wires, and the twist them together – positive to positive and negative to negative of course.

    The proper way is to unsolder the old battery and its wires and then solder the wires from the new battery in place.

  9. I’ve had it out for weeks now and it still doesn’t lower the volume like it should, and I pried the screen off the device as well.

    I’m sorry I still don’t understand what twisting looks like or accomplishes X___X

  10. Thank you very much, though. Everything was working until that point, the screen turned on and everything. Thanks again!!

  11. I mean by just twisting the wires together instead of soldering them. It wouldn’t be as durable but it might work.

    Have you made sure it is completely dry? It would take a while for all the water to dry out of that enclosed space, so maybe it is still in there and short circuiting the buttons? You can put it in a bag of rice or leave it out in the sun and air for a few days, depending on how long you have already left it.

  12. It’s extremely odd, the volume button lowers the volume instead of raising it. Yes, it powers on and works fine and plays music only when plugged in, when I unplug it from the wall outlet it just dies and won’t wake again til it’s plugged in.

    I’m not sure what you mean by the hack fix? Could you show me what that is? Thank you bunches!

  13. Unless you have really good soldering skills and a tiny soldering iron, there isn’t much you can do to fix it, since it is in plastic. Getting a replacement may be possible but I don’t know where you’d get one outside and Apple repair shop or getting a used iPod (or one that doesn’t work but has the cable, in which case you could possible replace the logic board instead etc)

  14. The gold ribbon that wraps around the tab that is pulled out has a little slit in it, probably from when I was putting the screws back in. Do you have any ideas how to repair that, or If I could buy a replacement ribbon from anywhere? Thanks so much!!

  15. What do you mean by “the volume button goes up”? The battery should be fairly easy to replace as it is just attached by two wires I think. You would need to solder them most likely unless you do a quick hack fix and twist them together from the new battery to the existing wires.

    I’m gathering the iPod still plays music and works ok when it is plugged into the computer?

  16. Please, if you can help me, I can’t find any post close to matching my problem:

    My 6th gen nano went thru the washer, the problems I found to fix were 1) needs a new battery and 2) the – volume button goes up (like the + button). I have no idea how to fix this or what this is caused by. Any ideas/suggestions? I’ve never fixed any hardware before (I’m an artist, I fix everything cosmetically) so I’m pretty new at this, tho I don’t want to go out and pay someone $150 to repair a little thing that costs the same.

    Thank you Rennie!

  17. I don’t know exactly what you have done but if you have ripped the cable or something it may be to difficult to fix. Otherwise if it is only a metal contact maybe you can find a way to put it back there in the hope it will still work, using a tiny amount of glue to hold it there (but not between the metal parts since they must contact!)

  18. I used super glue to attach the shim to the power button and ended up needing to remove the shim, too big. Ended up tear the button from the assembly; can this be fixed if so how/
    Thanks in advance.

  19. That’s a nice solution! I don’t drink soft drink very much so I didn’t have that lying around! It would have been easier than trying to file down the tiny circle like I did 🙂

  20. Thanks Rennie for the great instructions. I found that a beer (or soda) can was about the right thickness for the shim, and that fingernail clippers worked great for trimming it down. Thanks again!

  21. Hey rennie, appreciate the great post. My power button is stuck and this is by far one of the best guides in helping me solve my issue this weekend. Apparently, there’s a tiny black plastic dot on each of the buttons that tend to get loose and even fall out of place. The trick is to expose it and be able to glue a tiny nob of tinfoil or thin piece of steel/plastic as a replacement.

  22. Thanks for a great guide of how to solve the problem! I followed your excellent instructions and now my iPod nano is working again. Great tip about having the screws attached to a magnet. I did that but anyway lost one which took me 20 minutes of searching before I found it again. Without the magnet I bet I would have lost all four screws. Furthermore I did not have any good screwdrivers but I actually managed to pull it off just by the use of my Swiss Army knife. I ended up using the blade of the small knife as a screwdriver. It worked OK.

  23. Pingback: Random Pick of the Day – Green Leaf | rennie ash ♪·

  24. So it doesn’t turn on by the button? It’s possible the problem is the metal “spring” plate is damaged, I forgot whether the one I fixed had this issue as well (in any case, the one I fixed won’t “click” but it turned on when you pressed down – after the fix of course). You probabaly could fix it using the same proceedure, I guess it’s up to you if you think you can open it up without damaging it 🙂

  25. Hi. I was wondering if you thought the same surgical procedure might work for me… 😉 My power button feels more loose rather than stuck, as if there is no grip when you press it down & there is none of the “clicking” feel that I used to get. So it won’t press down & when I shake the ipod it now rattles…. Any thoughts? It still turns on when I charge/connect to a computer. Thanks. You are a thing of legends!

  26. Glad it worked for you, and nice to know about the thickness lol, although I doubt many will actually measure what they use – I know I didn’t! 😉

  27. So no power even when plugged into a computer? Have you checked all the screen cables are plugged into the logic board? Hopefully you haven’t severed any of them accidentally…

    If you can access the storage on a computer then the problem will be screen related, if there is nothing then either the battery is somehow disconnected or you have damaged something on the logic board.

    Hopefully you can get it fixed… 🙂

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s